Новинки
Компания Avago Technologies представила новые микросхемы ALM-80110 и ALM-80210
подробнее >>
Сверхминиатюрные термокомпенсированные кварцевые генераторы
подробнее >>
GaN несогласованный транзистор компании RF Micro Devices
подробнее >>
Силовой N-канальный МОП-транзистор NTMFS4927N компании ON Semiconductor
подробнее >>
Монолитные интегральные схемы СВЧ переключателей компании Hittite Microwave
подробнее >>
Все новинки
|
2RS version
 | |
Standard
|
|
Maintenance required | |
Mating materials:
Steel on high-duty bronze
2RS version
Special version
2RS sealing
| Inner ring: |
Antifriction bearing steel, hardened, ground and polished.
| | Bearing shells: |
Sliding face made of high-duty bronze. Both shells have a male thread and are screwed into the housing. In this way, any required bearing clearance can be adjusted and then secured with the two vulcanised locknuts of the rubber bellows.
| | Rubber bellows: |
Synthetic rubber with vulcanised brass slipring and steel locknut.
| | Bushings: |
Tempering steel, hardened, bore and outside diameter ground, pressed into the inner ring. They are only used as intake of the brass abrasive rings of the rubber bellows. Due to their low thickness they are not decicated to transmit radial and axial forces into the spherical bearing.
| | Lubrication: |
The lubricant enters the lubricating groove through a cross hole in the outer ring.
| | Tolerances: |
To DIN ISO 12240-4, schedule K, except: d = H10, B = +-0,3
| | Note: |
With these rod ends, it is important to ensure that the tilt angle specified in the table is not exceeded, either while mounting or during operation, otherwise the rubber bellows may be damaged.
|
|
| | |
Standard
|
|
Maintenance-free |
Mating materials:
Steel on PFFE
2RS version
Special version
2RS sealing
| Inner ring: |
Antifriction bearing steel, hardened, ground and polished.
| | Outer ring: |
Brass lined with an antifriction film, consisting PTFE, cold formed around inner ring, outside diameter with thread, screwed into the housing and secured with the vulcanised locknuts of the rubber bellows.
| | Rubber bellows: |
Synthetic rubber with vulcanised brass slipring and steel locknut.
| | Bushings: |
Tempering steel, hardened, bore and outside diameter ground, pressed into the inner ring. They are only used as intake of the brass abrasive rings of the rubber bellows. Due to their low thickness they are not decicated to transmit radial and axial forces into the spherical bearing.
| | Tolerances: |
Acc. to DIN ISO 12240-4, schedule K, except: d = H10, B = +-0,3
| | Note: |
With these rod ends, it is important to ensure that the tilt angle specified in the table is not exceeded, either while mounting or during operation, otherwise the rubber bellows may be damaged.
|
| | |
| |
|
Новости
Компания Silicon Laboratories представила серию Si51x
в которую входят кварцевые генераторы и кварцевые генераторы
подробнее >>Компания KEMET представила керамические чип-конденсаторы
предназначенные для монтажа на единую монолитную структуру.
подробнее >> С праздником 23 февраля
подробнее >>Генераторы с низкой G-чувствительностью
для военных и промышленных приложений
подробнее >>Cнижение цен на модели
драйверов светодиодов AIMTEC
|
 |
